ASTM A Standard Specification for Steel Strip, High Carbon, Cold Rolled, General Requirements. Find the most up-to-date version of ASTM A at Engineering ASTM A, AM – Designation: A /A M – 02 An American National Standard Standard Spe.
| Author: | Kajijin Kekus |
| Country: | Iraq |
| Language: | English (Spanish) |
| Genre: | Sex |
| Published (Last): | 25 November 2012 |
| Pages: | 377 |
| PDF File Size: | 4.98 Mb |
| ePub File Size: | 8.81 Mb |
| ISBN: | 326-7-79726-772-2 |
| Downloads: | 45112 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Nikorn |
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Limits on such elements are by agreement between purchaser and supplier. When agreed by purchaser and supplier, other silicon ranges are permissible.
C When the chromium is speci? Originally published as A — The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.
ASTM A682 Grade 1074
The values listed are not exact conversions of the values listed in the inch-pound tables but instead are rounded or rationalized values. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
However, under SI the preferred term in mass. Combining values from the two systems will ast, in nonconformance with the speci? ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard. Notwithstanding the absence of a signature, the organization submitting the EDI transmission is responsible for the context of the report.
The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Asym 1—The term weight is used when inch-pound units are the standard. When the maximum manganese limit exceeds 1. Thickness Tolerances Plus or Minus, in. A portion of the coil may be discarded prior to cutting the samples for retest.
Within the text, the SI units are shown in brackets. Within the text, the SI units are shown in brackets.
Link to Active This link will always route to the current Active version of the standard. Current edition approved March 10, Each of the elements listed in Tables 2 and 3 and additional elements agreed upon by the purchaser and the supplier shall be included in the report of heat analysis.
Elements such as aluminum may be added in sufficient amounts to control the austenitic grain size. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Strip tolerance products may be available in widths wider than ?
In case of dissatisfaction with the results of the test, the manufacturer may make claims for a rehearing. A superscript epsilon e indicates an editorial change since the last revision or reapproval. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. When the amount of copper, nickel, chromium, or molybdenum is less than 0.
However, unless the order speci? Stay on Page Continue to Compass. C When edge, width and thickness are not de? When one or more of these elements is speci? Materials and Manufacture 5.
ASTM A, AM_百度文库
The astmm comprising the desired chemical composition are speci? NOTE 3—When the camber tolerances shown in Table 8 are not suitable for a particular purpose, cold-rolled strip is sometimes machine straightened.
Notwithstanding the absence of a signature, the organization submitting the document is responsible for the content of the document. Government procurement by the Defense Supply Agency, strip material shall q682 continuously marked for identi?
Note 1—The term weight is used when inch-pound units are the standard.
The results of analyses taken from different pieces within a heat may differ from each other and from the cast analysis. Note 1—The term weight is used when inch-pound units are the standard. It is 6a82 produced as a fully killed steel.
When the amount of vanadium, columbium, or titanium is less than 0. However, unless the order specifies the applicable “M” specification designation SI unitsthe material shall be furnished to inch-pound units. Number of Tests and Retests Over 12 Width Tolerance, Plus and Minus, in. If any of the retests fail to comply with the requirements, the coil shall be rejected. Conformance to SI tolerances is mandatory when the “M” specification is used.