ASTM DENGL I 0b3b | This standard is issued under the fixed designation D ; the number immediately following the. This standard is issued under the fixed designation D ; the number immediately 1 This test method is under the jurisdiction of ASTM Committee D10 on. The ASTM-D standard test method for drop test of loaded containers evaluates the capability of a container to withstand the sudden shock resulting from a.
| Author: | Moogusida Yozshulmaran |
| Country: | Bahamas |
| Language: | English (Spanish) |
| Genre: | Art |
| Published (Last): | 12 August 2012 |
| Pages: | 180 |
| PDF File Size: | 8.43 Mb |
| ePub File Size: | 9.25 Mb |
| ISBN: | 918-7-20172-151-2 |
| Downloads: | 35711 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Mijora |
If it fails, the next test will be a lower drop height. Sometimes a v5276 drop or d526 cycle from a height which caused cumulative damage of this procedure will not cause similar damage to the package or contents.
Therefore, environmental influences as present in a container are not taken into account: Replicate samples should be subjected to identical procedues to determine the consistency of the failure point. See Practice D for additional guidance. See Practice D for additional guidance. See Practice D for additional guidance. It is recommended that special atmospheres for conditioning be selected from those given in Practice D An inspection reflects the quality of products during the inspection — before loading, shipment, unloading and distribution.
The use of a log-normal distribution is often suggested but this requires the drop height increment to be a constant based on the logarithms of the drop height, thus the actual drop height increment would 5d276 with the drop height.
If there are more failures than passes, average the height of the passes and add 1?
ASTM-D5276
When the capability of a container to withstand rough handling is to be evaluated, pack the container with either the actual contents or a load simulating the contents. Typical types of drop cycles are as follows: This must be based on n, the number of passes or failures, and not n?
It is best to choose an odd number of test specimens. Neither the depth nor width of the mass shall be less than half the length.
Drop test of loaded containers (cartons), ASTM D | AQF
This test method may also be used to compare the performance of different package designs. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Click here for instructions on how to enable JavaScript in your browser. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Where a bag or sack has one or more side seams, Side 2 shall include a side seam. Historical Version s – view previous versions of standard.
How can I ensure aetm total quantity of my goods is shipped? While the outer carton almost always deforms, the products may still be protected from breakage. See Practice DAcceptance Criteria.
Quality Management View All. The test plan should also consider the type of information desired from the testing: ASTM-D Standard Test Method for Drop Test of Loaded Containers by Free Fall The ASTM-D standard test method for drop test of loaded containers evaluates the capability of a container to withstand the sudden shock resulting from a free fall, or the capability of a container and its inner packing to protect its contents during the sudden shock resulting from a free fall.
Precision and Bias Continue dropping on similar cycles until a speci? Astm D Standard If the dropping surface is a steel plate, it must be at least 1? Your email address will not be published. Link to Active This link will always route to the current Active version of the standard.
Drop test of loaded containers (cartons), ASTM D5276
These ISO standards may describe procedures that do not meet the requirements for this test method. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.
During transport, cartons are subject to shock, vibration, humidity and pressure. Purchase Process View All. Where it is desirable to drop on a midpoint aastm two locations on the chime, such a point can be designated using two numbers, that is, drop on Quality control inspection companies often simply refer to it as the carton drop test.
ASTM-D – Medical Package Testing
The drop height increment is a constant and should be between 1? Caution—These ISO standards may describe procedures that do not meet the requirements for this test method.
If this specimen passes at this drop height, the next test will be at a higher drop height with a new package. With the Quality Control Blog we want to tell stories taken from our daily activity to help the importers in sourcing better and safer.
Standard Test Method f Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Where a hazard other than that speci?