Standard Test Methods for Chemical Analysis of Zinc and Zinc Alloys. Status: Withdrawn · Replaced by: ASTM E Buy this standard. Price: SEK. PDF. Feb 1, These test methods for the chemical analysis of zinc metals and alloys are primarily intended as referee methods to test such materials for. Find the most up-to-date version of ASTM E at Engineering
| Author: | Zulut Tojahn |
| Country: | Uzbekistan |
| Language: | English (Spanish) |
| Genre: | History |
| Published (Last): | 2 September 2008 |
| Pages: | 63 |
| PDF File Size: | 4.88 Mb |
| ePub File Size: | 19.51 Mb |
| ISBN: | 440-6-78809-384-4 |
| Downloads: | 54800 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Gardarg |
A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense.
NOTE 1—Certain continuous galvanizing grades are speci? Other continuous galvanizing and controlled lead grades are not included in this speci? The values given in parentheses are for information only.
It is the responsibility of the user of this standard to become adtm with all hazards including f536 identi? Current edition approved Nov. Originally approved in Last previous edition approved in as B 6 — For purposes of determining conformance with this speci? Total Non-Zinc, max 0.
Refer to Practice B Materials and Manufacture 5. Sizes and Shapes 7. Sampling for Chemical Analysis 9. The portion preferably shall be taken during loading or unloading. From lots containing at least 60 lb 27 kg of zinc, one slab shall be taken from every 10 lb kg. The drillings or sawings shall be subjected to the action of a strong magnet to remove any adventitious iron with which the sample may have become contaminated from the drill or saw.
If two holes from each slab do not yield the weight of sample prescribed in 9.
ASTM A105 Threaded Forged Steel Nipple (YZF-E536)
Each hole shall be bored completely through the slab, care being taken to avoid starting the drill in a depression and to adjust the feed to give drillings 0. The drill used preferably shall be one twisted from?
The diameter of the drill shall be 1? The drillings shall be broken or cut with clean shears into pieces not over 1? E56 cut shall be approximately halfway between the center and each end.
ASTM E536 – 16
The width of the saw cut shall be sufficient to give the weight of sample prescribed in 9. The properly mixed sample shall be split into three equal parts, each of which shall be placed in a sealed package, one for the manufacturer, one for the purchaser, and one for a referee, if necessary. Tight, leak-proof, paper sample envelopes or cardboard cartons may be used to hold the sample.
Methods of Chemical Analysis asttm The manufacturer shall be given one 1 week from date e5336 receipt of such claim to investigate his records and then shall agree either to satisfy the claim or send a representative to the plant of the purchaser. Ast, of Claims If agreement is not reached, the question of fact shall be submitted to a mutually agreeable referee, whose decision shall be? The manufacturer and the purchaser shall adtm make an analysis, and if the results do not establish or dismiss the claim to the satisfaction of both parties, the third sample shall be submitted to a mutually agreeable referee, who shall determine the question of quality, and whose determination shall be?
Aetm of Claims In case of rejection being established, maximum damages shall be limited to the payment of freight both ways by the manufacturer for substitution of an equivalent weight of zinc metal conforming to this speci?
ASTM-USA-第95页-标准图书馆
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters.
Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.