Default Re: Huawei CDMA E BTS Max Power??? HI I think it can be more than 20W because the RF board support MAX 60W. The 3rd Global CDMA Operation and Development Forum, themed. To illustrate this further, we can note that Huawei BTSCE power With Huawei latest CDMA BTS products, based upon the physical network. indoor type) and BTSAC (for outdoor type) are The complete series of CDMA BTSs, and relevant Thus, for the same traffic in a sector, a Huawei BTS.
|Published (Last):||21 April 2015|
|PDF File Size:||17.92 Mb|
|ePub File Size:||3.45 Mb|
|Price:||Free* [*Free Regsitration Required]|
For the 24 V power input, the voltage drop of the cable from the 24 V power supply system to the power input port of the BTS must be less than or huwaei to 0. To print the manual completely, please, download it. Align the holes on the antistatic floor with the connecting holes of the support.
Leveling the lower support See section 2. O 2 Configuration The O 2 refers to an omni cell with two carriers. That is, 1 m 39 in. Environmental Protection This product has been designed to comply with the requirements on environmental protection. Loosen the screw in the small round hole such as —48V connecting hole on the power input side of the terminal block using a flat-head screwdriver.
The sectional area is 35 cables VL: The last section also explains how to install cabinet assemblies on the cement floor without sufficient bearing capacity. Thus, you do not need to install these cables on site. Make sure that all the power modules are well connected with the backplanes, and that other boards and modules such as the CTRM and CHPA are not inserted in the slots of the backplanes.
HUAWEI BTS INSTALLATION MANUAL Pdf Download.
Fix them onto the units. Page 14 – Power Supply Conditions of the Equipment Determine the length of the grounding cables according to their actual cabling path, that is, the route from the binding post of 366 cabinet to the wiring holes of the grounding protection bar of the cabinet.
Installing Other Functional Modules Cdmq, the fan box is installed upon delivery. Do not bend an optical fiber to a right angle upon distribution. Place the support below the antistatic floor.
Wooden cases are generally used to pack heavy objects like racks, batteries, and so on. Outline Figure shows the outline of the lower support.
If the outer package is damaged or soaked; or the equipment is soaked and becomes rusty, stop unpacking and find the cause. Connect one end of the cable to the working ground of the EAC. Tools The following tools are required: For the proper storage, use and disposal of this product, national laws and regulations must be observed. The following items must be checked Conducting Insulation Test To conduct an insulation test, proceed as follows: The packing case is in good condition.
CDMA grows greener
Administration Building, Huawei Technologies Co. No field installation of the fan box is required. Chapter 1 Installation Preparations 1. Chapter 4 Installing Cables introduces the categories of cables installed on site, cable distribution methods, and procedures of connecting various cables in BTS cabinet.
Cut the tapes huawel the seams of the carton cover using a knife. Lead the cables into their corresponding cable-fixing troughs.
Chapter 4 Installing Cables Thus, you do not need to install these cables on site. The letters A, B, C as shown in Figure are not cable labels.
Huawei CDMA E BTS Max Power ???
The alarm box is correctly installed according to the design. Lead the bolts through the lower support. Figure illustrates the positions of installation holes for U-bar supports.
To avoid damaging equipment inside, do not apply too much force. Means a complementary description.
Outline Figure shows the outline of A series support. This manual also for: Page 70 – Distributing Protection Grounding Cables Enter text from picture: It is divided into six chapters: When handling the cabinet, hold on the solid places such as the upper cable rack or bone frame.
Huawei BTS3606 Installation Manual
Figure Installing a board 2 Tighten the screws clockwise on the front panel, as shown in Figure Don’t show me this message again. Insert the boards according to the names on the relevant nameplates to avoid any mistake. All Rights Reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co. Installing the Lower Support To install the lower support, proceed as follows: The panel is clean without obvious damage.
Determine the installation location for the DDF according to the engineering design for the equipment room. The color of the coat must be the same as or similar to that of the cabinet.